Flowtech Measuring Instrument Private Limited

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Installation Orifice Plate gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Features:

• Flow measurement
• Perfect results
• Simple to maintain

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

Fowtech Make Orifice Flange Assemblies are used for measuring flow of various Liquids, Gases & Steam from 2 to 32 line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of Differential Pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice  flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Design Calculation Orifice Plate gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Features:

• Flow measurement
• Perfect results
• Simple to maintain

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

 
Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Flowtech make Orifice Type Flow Meter are used for measuring flow of various Liquids, Gases & Steam from  2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Other Details:

• Flowtech Make Orifice Plates & Flange Assemblies.
• Suitable for creating differential pressure in a pipe line for flow transmitter etc.
• Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

 
Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Flowtech Make Orifice Plates & Flange Assemblies.Suitable for creating differential pressure in a pipe line for flow transmitter etc. Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets. Flowtech make WNRF Orifice Type Flow Meters are used for measuring flow of various Liquids, Gases & Steam from 1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Features:

• Flow measurement
• Perfect results
• Simple to maintain

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Orifice Plate Meter gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Features:

• Flow measurement
• Perfect results
• Simple to maintain

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Orifice Flange Assembly gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Features:

• Flow measurement
• Perfect results
• Simple to maintain

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

“fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Flowtech make Orifice Plates and Flange Assembly are used for measuring flow of various Liquids, Gases & Steam from 1 ½” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Flowtech make Orifice Flange Assembly are used for measuring flow of various Liquids, Gases & Steam from 1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Flowtech make Orifice Flange Assemblies are used for measuring flow of various Liquids, Gases & Steam from 1 ½” to 24” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Description:

• Flowtech Make Orifice Plates & Flange Assemblies.
• Suitable for creating differential pressure in a pipe line for flow transmitter etc.
• Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets. 

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Orifice Plates Water Flow Meter gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Features:

• Flow measurement
• Perfect results
• Simple to maintain

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Orifice Plate Meter gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Features:

• Flow measurement
• Perfect results
• Simple to maintain

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

“fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.

Flowtech make Flange Assemblies are used for measuring flow of various Liquids, Gases & Steam from 2" to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Other detail:

• Flowtech Make Orifice Plates & Flange Assemblies.
• Suitable for creating differential pressure in a pipe line for flow transmitter etc.
• Orifice flange assemblies’ consist of weld neck type flanges with studs, nuts, and gaskets.
• Available in SS-316/ P.P. Material.
• Design standard confirm to BS 1042
• Design Standards
• Design - Confirming to ISA RP 3.2, DN 1952, BS 1042, ISO-5167
• Orifice Bo re - Confirming to ISO 5167 / BS 1042 / RW Miller / L. K. SPINK / AGE – 3
• VENT / DRAIN - Vent OR Drain holes are provided as per customer’s requirement. Not drilled for Orifice Bore smaller than 25.4 mm.

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate With WNRF Flange Assemblies gives an acceptable level of uncertainties at lowest cost and long life without regular maintenance. These products from our side are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of differential pressure created when an obstruction is placed in the fluid flow, due to increase in fluid velocity.

Features:

• Flow measurement
• Perfect results
• Simple to maintain

Applications:

• Scientific laboratory
• Research centres
• Chemical industries

“Fowtech” Make “orifice Flange Assemblies” are used for measuring flow of various Liquids, Gases & Steam from 2” to 32” line sizes. It gives an acceptable level of uncertainties at lowest cost and long life without regular maintenances. Orifice Plates are most commonly used as primary element for flow measurement in pipelines based upon the principle of measurement of ‘Differential Pressure’ created when an obstruction is placed in the fluid flow, due to increase in fluid velocity. The orifice plate dimension is based on BS/ISO- 5167 specification.

Operating Principal:

• When fluids is flowing from main pipeline. Orifice plate restricts the flow and develops the Differential Pressure which is proportional to the square root of the flow rate.

Design:

• The traditional orifice flange assembly consists of a pair of flanges, orifice plate, bolts, nuts, gaskets, jacking screws and plugs, (where requested). The flanges are generally weld neck design, but other options are available, such as Slip-on and threaded.

Weld neck Orifice Flange Assemblies:

• Weld neck orifice flanges are butt-welded into the pipeline. The inside diameter (or the schedule) of the pipe should be specified when ordering. Weld neck orifice flanges are available in classes 150,300 & 600. Raised face (RF) and ring type joint (RTJ) versions can be supplied. Bolt sizes, weights and important dimensions of orifice flange assemblies are shown in the following tables.

Orifice Plate Flange Assembly Component:

• The orifice – flange assembly consists of a mainline Orifice plate, a set of Orifice Flanges. This plate is sandwiched between two Orifice Flanges. Tag Plate of orifice plate projects out from Orifice flanges and it indicates the existence of Orifice plate. Details such as Tag NO /Orifice ID / Pipe ID / Plate Material are stamped on one side of the tag plate which faces upstream side of the pipe line.