Flowtech Measuring Instrument Private Limited

Application:

• S.S. body and rotor Flow measurements of Pharmaceutical, Drug, Food, Oil, Water and all application.

Material Of Construction :

• Enclosure     : S.S-304/S.S-316
• Rotor             : S.S-304
• Shaft              : Hard Stainless Steel-316 with carbon bush
• Accuracy (standard installation position): +/- 0.5 OR 1% FSD
• Repeatability: 0.1%
• Maximum working Pressure: 6 MPa
• Fluid & Ambient Temperature: -20º C to 120º C
• Connection: Threaded (M/F) OR Flanged
• PULSE OUTPUT SENSOR :-
• Power voltage         : 12 V DC
• Output signal           : NPN open connector
• High electric level   : Higher than 8 V DC (input voltage 12 VDC)
• Low electric level   : Lower than 0.8 V DC (input voltage 12 VDC)

 

Application:

• Diesel Flow meter is a kind of positive displacement Meter to measure the liquid flow or instantaneous flow of the Pipe tube.
• lt is a kind of accumulate meter. WithCharacteristics of high accuracy, small change by the fluid Viscosity,
• It is widely used to measure oil kind liquid, forbidden to measure corrosive.

Working Principle:

• The measurement part of oval gear flow meter is posed by two elliptical gears mesh with each other and its shell (measuring room). The figure shows that the flow meter works by two elliptical gears to mesh with each other, its working process are as follows: P1 in the figure shows the pressure of liquid from inlet side, to show the outlet pressure, the bottom rotor has no rotating torque even it effected the liquid pressure, but the above gears will move by the rotatingPressure .ln the status of the above gears driving gear, and the bottom gear is driven gear. both of these two gears have rotating torque by the liquid pressu/'e, and they move with the direction of the arrow to space The gear space is opposite to, the bottom gear is driving gear, and above gear is driven gear. The bottom gearpushes the liquid out from the half moon space under the liquid press pushes liquid volume four times of "measurement room". So, as long as the rotation of gears, the liquid volume can be counted.

A turbine flow meter is used for volumetric total flow and/or flow rate measurement and has a relatively simple working principle. As fluid flows through the turbine meter, it impinges upon turbine blades that are free to rotate about an axis along the center line of the turbine housing. The angular (rotational) velocity of the turbine rotor is directly proportional to the fluid velocity flowing through the turbine. The resulting output is taken by an electrical pickoff(s) mounted on the flow meter body.

Product Features:

• Highly sensitive to low flow rates
• Very accurate over its entire flow range

Technical Datasheet : 

• Enclosure : S.S-304/S.S-316Rotor       : S.S-304
• Shaft : Hard Stainless Steel-316 with carbon bush
• Accuracy (standard installation position) : +/- 0.5 OR 1% FSD
• Repeatability : 0.1%
• Maximum working Pressure : 6 MPa
• Fluid & Ambient Temperature : -20º C to 120º C
• Connection : Threaded (M/F) OR Flanged

Pulse Output Sensor:

• Power voltage : 12 V DCOutput signal : NPN open connector
• Output :High electric level : Higher than 8 V DC (input voltage 12 VDC)Low electric level : Lower than 0.8 V DC (input voltage 12 VDC)

Battery Operated Meter :

• Power voltage : 3.3 V10AH lithium batteries can be used more than 5 years in a row.
• Display mode : Double row Liquid Crystal Display (LCD), as follows:L XXX. X four instantaneous flow (M³/Hr) orL/h XX. XXXXXX eight cumulative flow (M³)
• Cumulative flow automatically expands the display precision
• The cumulative flow values can be reset
• Power-fail protection instrument coefficient
• The Total flow values are not lost for ten years when power supply drop
• Display With 4 To 20 Ma Output:
• Power voltage : 24 V DCOutput signal : 4 TO 20 mA

Application :

• Turbine flow meters are used to measure clean, dry gases and liquids such as hydrocarbons,chemicals, gases and vapours, fuels and other types of liquids with lower viscosity, and for applications requiring highly accurate and precise measurements. They are applicable in S.S. body and rotor flow measurements of Pharmaceutical, Drug, Food, Oil, Water and all other applications.

Application :

• Diesel Flow Meter is a kind of positive displacement Meter to measure the liquid flow or instantaneous flow of the Pipe tube. lt is a kind of accumulate meter. With Characteristics of high accuracy, small change by the fluid Viscosity, it is widely used to measure oil kind liquid, forbidden to measure corrosive.

Working Principle:

• The measurement part of oval gear flow meter is posed by two elliptical gears mesh with each other and its shell (measuring room).The figure shows that the flow meter works by two elliptical gears to mesh with each other, its working process are as follows: P1 in the figure shows the pressure of liquid from inlet side, to show the outlet pressure, the bottom rotor has no rotating torque even it effected the liquid pressure, but the above gears will move by the rotating
• Pressure ln the status of the above gears driving gear, and the bottom gear is driven gear. both of these two gears have rotating torque by the liquid pressu/'e, and they move with the direction of the arrow to space The gear space is opposite to, the bottom gear is driving gear, and above gear is driven gear. The bottom gear pushes the liquid out from the half moon space under the liquid press pushes liquid volume four times of "measurement room". So, as long as the rotation of gears, the liquid volume can be counted.

Technical Data